| Tool spindle full indexing
specifications |
Erhöhung der mögl. Indexierung der
B-Achse auf 0,0001º Einrichtung zur Positionierung der B-Achse mit
einem minimalen Winkel von 0,0001º anstelle der Standardausführung
mit 1º, einschließlich der Option Direktes Wegmesssystem in der
B-Achse der |
| Spindle 2 tailstock specifications |
Spindle 2 tailstock specifications You can use
spindle 2 also as a tailstock. The servo motor on the B-axis equips a
brake to prevent spindle 2 from going back in case of emergency stop
or power failure. Center is fitted by clamping it with chuck´s
jaw. |
| Preparation for automatic centering
steady rest SMW SLU-6Z (servo-driven) (single) (/3000, /4000) (High
Rigidity specification) |
Preparation for Automatic Centering Steady Rest
SMW SLU-6Z (Servo- driven) (Single) (/3000, /4000) (High Rigidity
Specification) This is an I/F for automatic centering steady rest body
attachment. The steady rest prevents vibration and deflection of a
lo |
| Coolant float switch (lower limit
detection) |
Coolant Float Switch (Lower Limit Detection) It
controls the coolant level (lower limit detection). An Alarm is
displayed on the operation panel when the coolant falls below the set
level. |
| Knoll KF110/700 Filter System 7.0
MPa |
Knoll KF110/700 Filter system 7.0 MPa - 31 l/min -
5.5kW high pressure coolant pump - vario valve - paper filter - 700 l
coolant tank with cleaning opening - float switch - electrical
connection 3x400 V - hose assembly (5m) and interface cable (10m).
With |
| Super-high-pressure coolant system I/F
(7.0 MPa, KNOLL) |
Super-high-pressure coolant system I/F (7.0 MPa,
KNOLL) We have prepared an I/F for the high-pressure coolant unit
(Knoll). High pressure coolant unit main body (Knoll) is not included
in this specification. |
| Air blow for tool tip (tool spindle) |
Air blow for tool tip (tool spindle) The air blow
removes chips adhering to the tool tip. The air blow is controlled by
M codes in the program. The air blow is turned on by M458, and off by
M459. |
| Chip conveyor (right discharge, hinge
type) (/3000) |
Chip conveyor (right discharge, hinge type)
(/3000) Chips are loaded onto hinge type plates and discharged outside
the machine. This is effective when discharging long chips. It is not
suitable for discharging minute powdery chips generated when
machini |
| In-machine workpiece measuring system
radio signal transmission type touch sensor (Renishaw) RMP60 |
In-machine workpiece measuring system
radio-transmission type touch sensor (Renishaw) The sensor tool
installed on the turn-mill spindle measures the machined workpiece
and transmits a signal through radio waves to register the measured
results in cust |
| Full-closed loop control for X-axis
(Turn-mill Spindle) (Direct scale feedback) |
Full-closed Loop Control for X-axis (Turn-mill
Spindle) (Direct Scale Feedback) The magnetic scale is used for the
X-axis position sensing of the Turn-mill Spindle, instead of the axis
servomotor pulse encoder. It is not susceptible to ball screw
preci |
| Full-closed loop control for Y-axis
(Turn-mill Spindle) (Direct scale feedback) |
Full-closed Loop Control for Y-axis (Turn-mill
Spindle) (Direct Scale Feedback) The magnetic scale is used for the
Y-axis position sensing of the Turn-mill Spindle, instead of the axis
servomotor pulse encoder. It is not susceptible to ball screw
preci |
| Full-closed loop control for Z-axis
(Turn-mill Spindle) (/3000) (Direct scale feedback) |
Full-closed Loop Control for Z-axis (Turn-mill
Spindle) (/3000) (Direct Scale Feedback) The magnetic scale is used
for the Z-axis position sensing of the Turn-mill Spindle, instead of
the axis servomotor pulse encoder. It is not susceptible to ball
scr |
| Automatic door (/3000) |
Automatic door (/3000) The front door can be
opened and closed automatically by a motor. A tape switch is installed
in the front door. When an operator is caught in the door, the tape
switch is activated and immediately stops the door. When this
specific |
| Chuck foot switch (double) for spindle 1,
2 |
Chuck foot switch (double) for spindle 1, 2 Chuck
opening and closing on spindle 1 and 2 are operated by twin chuck
footswitch. |
|
|
| 5 external M-codes |
5 external M-codes This function contributes and
expands the existing M-codes. To add this, let the M-codes output
pass through the relay and dispose terminal block connected to the
A-contact on the MTX substrate.(Terminal 1 and 2) We will prepare 5
in |
| Programming resolution multiplied by
1/10 |
Programming resolution multiplied by 1/10 Minimum
setting unit and minimum traveling unit can be changed to 0.0001 mm
from the standard 0.001 mm. This is effective for precision machining
to enhance surface roughness or dimensional accuracy on
workpieces |
| Tool spindle Cs control |
Tool spindle Cs control This function allows tool
spindle to be positioned at D1252871 arbitrary angle by distributing
E-axis to tool spindle rotation. Order design specification must be
issued. Tool spindle Cs control includes normal direction controland
Cs |
| Part program storage length 8 MB (20,480
m) in total + Registerable programs 4,000 in total (AI contour control
II is needed) |
Part Program Storage Length 8 MB (20,480 m) in
Total + Registerable Programs 4,000 in Total (AI Contour Control II
is Needed) The storage capacity of CNC can be increased to 8 MB
(20,480 m) to register up to 4,000 programs. |
| Spiral/ conical interpolation |
Spiral/ conical interpolation Spiral interpolation
is executed by specifying the spindle speed or the amount of radius
increase/decrease per spindle rotation in addition to the circular
interpolation command in the same block. Conic interpolation is
execu |
| NURBS interpolation (SK-OP) |
NURBS Interpolation It enables programming of the
NURBS curve which is a widely used method for creating free curves.
Since the high-precision NURBS curves interpolation is conducted, the
smoother machined surface, which is very close to the designed s |
| DXF Import function |
DXF Import function By importing 2D CAD data (DXF
data), data for workpieces with complex contours can be input easily.
Data import is possible in the GENERAL, MILLING, and HOLE processes of
the machining menu. ·Program creation time is substantially re |
| Program number 8-digit O code |
Program number 8-digit O code The program number
is 8-digits. Control unit:MSX-701, MSX-711 Standard:4-digits
Option:8-digits |
| Manual handle interruption |
Manual Handle Interruption For slightly shifting
the tool or making it cut in during the automatic operation, rotating
the manual pulse generator can moves the tool by the amount of the
output pulses without suspending the machining. Afterwards, the
work |
| Program restart |
The program restart function allows the program to
be restarted from a desired block if a tool is broken or for
restarting the suspended operation after holidays. To restart the
program, specify the sequence number of the block or the block number
to b |
| Additional workpiece coordinate systems
300 sets |
Additional workpiece coordinate systems 300 sets
When the standard 6 sets of workpiece coordinate systems (G54 - G59)
are not sufficient, up to 300 sets of workpiece coordinate systems can
be added. |
| Automatic corner override |
Automatic Corner Override For creating inner
corners or inner arcs using a tool with tool offset, the excellent
cutting surfaces can be obtained by automatically slowing the
feedrate of the tool to reduce load on it. G62: Automatic Corner
Override comma |
| Coordinate system rotation |
Coordinate system rotation Shapes specified by
programs can rotate centering around a fixed point. |
|
|
| Transformer 160 kVA |
Three-phase autotransformer in cabinet, power 160
kVA, primary voltage 400V, secondary voltage 200V, rated frequency
50Hz, incl. main switch and mains filter, type: CLPB 80F-
1427T20001 |